Screw in vent valve XINXIA-LWVV_M101.5-10
PRODUCT NAME |
Screw-In Vent Valve |
PRODUCT MODEL |
XINXIA-LWVV_M101.5-10 |
PRODUCT DIAGRAM |
|
MEMBRANE MODEL |
XINXIA-TB20WO-E |
Product Properties
PHYSICAL PROPERTIES |
REFERED TEST STANDARD |
UNIT |
TYPICAL DATA |
Thread SPEC |
/ |
/ |
M10*1.5-10 |
Valve Color |
/ |
/ |
Black/White/Gray |
Valve Material |
/ |
/ |
Nylon PA66 |
Seal ring Material |
/ |
/ |
Silicone Rubber |
Membrane Construction |
/ |
/ |
PTFE/PET non-woven |
Membrane Surface Property |
/ |
/ |
Oleophobic/Hydrophobic & |
Typical Air Flow Rate |
ASTM D737 |
ml/min/cm2 @ 7KPa |
2000 |
Water Entry Pressure |
ASTM D751 |
KPa dwell 30 sec |
≥60 |
IP Grade |
IEC 60529 |
/ |
IP67/IP68 |
Water Vapor Transmission Rate |
GB/T 12704.2 (38℃/50%RH、) |
g/m2/24h |
>5000 |
Service Temperature |
IEC 60068-2- 14 |
℃ |
-40℃ ~ 125℃ |
ROHS |
IEC 62321 |
/ |
Meet ROHS Requirements ( ROHS ) |
PFOA & PFOS |
US EPA 3550C & US EPA 8321B |
/ |
PFOA & PFOS Free |
Installation Notes
1.The Installation hole size adopts the general standard of M10*1.5.
2. It is recommended to fix the cavity with nuts when the wall thickness of the cavity is less than 3mm.
3. When it needs to install two breathable valves, it’s suggested that the valves should be installed in opposite directions to reach the air convection effects.
4. Suggested installation torque is 0.8N.m, lest torque too much to affect the product performance.
Application
Changing harsh environmental conditions cause seals to failand allow contaminants to damage sensitive electronics.
XINXIA® Screw-In Breathable Valve effectively equalize pressure and reduce condensation in sealed enclosures, while keeping out solid and liquid contaminants. They improve the safety, reliability and service life of outdoor electronic devices. XINXIA® Screw-In Breathable Valve is designed to provide Hydrophobic/Oleophobic protection and withstand the mechanical stresses of challenging environments.
Shelf Life
Shelf life is 5 years from the date of receipt for this product as long as this product is stored in its original packaging in an environment below 80° F (27° C) and 60% RH.
Note
All data above are typical data for the membrane raw material, for reference only, and should not be used as special data for outgoing quality control.
All technical information and advice given here is based on XINXIA’s previous experiences and test results. XINXIA gives this information to the best of its knowledge, but assumes no legal responsibility. Customers are asked to check the suitability and usability in the specific application, since the performance of the product can only be judged when all necessary operating data are available.
application of waterproof vent valve Outdoor lighting
LED outdoor lighting is another typical application of waterproof ventilation valves. Outdoor LED lamps are usually waterproof and sealed, but this will also bring the problem of heat dissipation. On the one hand, the high temperature will cause the failure and failure of the components in the LED lighting system; On the other hand, in order to avoid the damage of high temperature to the lighting system, many LED lamps are designed with temperature control devices, when the working temperature of the LED lamp exceeds the set value, the equipment will enter the protection state, affecting the normal use. In order to prevent these situations, it is necessary for the waterproof ventilation valve to play a role - when the temperature in the LED lamp rises and the pressure becomes larger, the hot air in the lamp is discharged through the breathable waterproof valve, and the pressure inside and outside the equipment is balanced in time and the heat is accelerated to ensure the normal operation of the equipment.
-
XINXIA-LWVV_M101.5-10.PDF
Download